GPU Repair Hong Kong: Fix Black Screen & BGA Reballing

2026-11-12 | VRAM Upgrade | 21 分鐘 | HK GPU Fix Editorial

GPU Repair Hong Kong: Fix Black Screen & BGA Reballing

重點摘要

RTX 4090 黑屏/花屏維修約 HK$800–$1,800,BGA 核心重植 HK$1,200–$2,000,風扇不轉(PWM IC)HK$600–$900,PCIe 金手指斷裂修復 HK$700–$1,200。一般 2–4 個工作天完成,保養 90 天。

Introduction

I've been fixing graphics cards in Hong Kong for over 15 years, and I can tell you this: the problems haven't changed much, but the cards have. An RTX 4090 that black-screens on you isn't cheap to replace, and with fake cards flooding the market, repair is often the smarter move. In this article, I'll walk you through the four most common GPU faults I see every week — black screen and artifacts, BGA core issues, fan failures, and broken PCIe gold fingers — and explain how we actually fix them at ComputerKing.

Whether you're a gamer, a content creator, or someone who just wants their workstation back, this guide will give you a realistic picture of what's fixable, what it costs, and when to cut your losses.

What causes RTX 4090 black screen and artifacts?

RTX 4090 black screen and artifacts are usually caused by a failing GPU core, faulty VRAM, or a cracked solder joint under the BGA package — not by a driver problem. In my experience, over 70% of RTX 4090 black-screen cases that come through our Sham Shui Po workshop are hardware-related, and a FLIR thermal camera can pinpoint the exact fault within 15 minutes. The 4090 runs hot, and the constant heating and cooling cycles in Hong Kong's humid climate put stress on the solder joints. When the card heats up, a micro-crack under the core or VRAM chip opens up, and you get a black screen, green lines, or full-screen artifacts.

The first thing we do is a visual inspection and thermal imaging. If one VRAM chip is running significantly hotter than the others, that's your culprit. If the whole core area is cold but the card is powered, it could be a power delivery issue. We then run a memory test to confirm which chip is failing. For RTX 4090 cards, VRAM faults are common because the memory runs at high speeds and generates a lot of heat. Replacing a single VRAM chip costs around HK$800–$1,200, while a full BGA reball of the core is HK$1,200–$2,000.

BGA core reballing: when is it needed and how does it work?

BGA core reballing is needed when the solder balls under the GPU core have cracked or oxidised, causing intermittent connections or complete failure. This is a chip-level repair that requires a rework station, stencil, and a lot of patience. In Hong Kong, not many shops offer true BGA reballing — many just reflow the card with a heat gun, which is a temporary fix that often fails within weeks. A proper reball involves removing the core, cleaning the pads, re-balling with leaded solder (for better reliability), and re-soldering with precise temperature control.

We've seen a surge in BGA issues on RTX 4090 and 5090 cards, especially those that have been mining or running heavy AI workloads. The constant thermal cycling fatigues the solder. Symptoms include black screen, no display, or the card not being detected at all. A reball typically takes 3–4 hours and costs HK$1,200–$2,000 depending on the card. We always recommend this over buying a used card, especially with so many fakes around.

Why is my GPU fan not spinning? PWM control IC failure

A GPU fan not spinning is often caused by a failed PWM control IC on the card's PCB, not by the fan motor itself. This is a common fault in Hong Kong because of dust and humidity. The PWM IC regulates fan speed based on temperature; when it fails, the fan either runs at full speed constantly or doesn't spin at all. Many people assume the fan is dead and buy a replacement, but the real issue is on the board. We test the fan with an external power source first — if it spins, the fan is fine and the IC is the problem.

Replacing a PWM IC is a micro-soldering job that costs around HK$600–$900. We've done hundreds of these, and the success rate is high. If left unfixed, the GPU will overheat and throttle, and eventually the core or VRAM can fail. So if you notice your fans aren't spinning, don't ignore it.

PCIe gold finger damage: cracked traces and broken pins

PCIe gold finger damage — cracked traces, broken pins, or worn contacts — is a common result of improper installation, heavy card sag, or repeated removal. The PCIe slot carries power and data; if the gold fingers are damaged, the card may not be detected, or it may cause system crashes. In Hong Kong, we see this a lot with second-hand cards that have been swapped in and out of mining rigs. Repairing gold fingers involves micro-soldering to rebuild the traces and, in some cases, replacing the entire connector.

The cost for PCIe gold finger repair is around HK$700–$1,200, depending on the severity. We always test the card in a known-good system after repair to ensure stable operation. If the damage is too extensive, a donor board swap might be more cost-effective — we'll discuss that with you before proceeding.

How much does GPU repair cost in Hong Kong?

GPU repair in Hong Kong typically costs between HK$600 and HK$2,000, depending on the fault. Here's a quick breakdown based on our 2026 price list:

Fault TypeTypical Cost (HKD)Turnaround Time
Fan not spinning (PWM IC)$600–$9001–2 days
PCIe gold finger repair$700–$1,2001–2 days
VRAM replacement (single chip)$800–$1,2002–3 days
BGA core reballing$1,200–$2,0003–4 days
Donor board swap$1,500–$2,5003–5 days

These prices are for labor and basic parts; high-end cards like the RTX 4090 may be at the higher end. We always inspect first and give you a quote before any work begins. If the card is not repairable, we'll tell you honestly — no charge for inspection if you proceed with repair.

When should you repair vs replace?

Repair is usually worth it if the card is high-end (RTX 4080/4090/5090) and the repair cost is less than 40% of a replacement. For older or lower-end cards, replacement might make more sense. Also consider the warranty — our repairs come with a 90-day warranty on the work performed. If you're unsure, bring it in and we'll help you decide.

Frequently Asked Questions

Q: Can a black-screen RTX 4090 be fixed permanently?

A: Yes, if the fault is a cracked solder joint or VRAM chip, a proper BGA reball or chip replacement can restore it permanently. We've fixed hundreds of 4090s with a high success rate.

Q: How long does BGA reballing take?

A: Typically 3–4 working days, including testing. We'll keep you updated via WhatsApp.

Q: Do you offer warranty on GPU repairs?

A: Yes, all repairs come with a 90-day warranty covering the repaired fault.

Q: Can you fix a GPU with physical damage like a broken PCIe connector?

A: In most cases, yes. We can rebuild traces or replace the connector. We'll assess and quote first.

Q: Do you repair fake RTX 4090 cards?

A: We can often repair them, but we'll also advise you on whether it's worth it. Some fakes have poor-quality components that fail again.

Conclusion

GPU repair in Hong Kong doesn't have to be a nightmare. With the right diagnosis and chip-level repair, many cards that seem dead can be brought back to life. If you're dealing with black screens, artifacts, fan issues, or PCIe damage, don't rush to buy a new card — especially with the fake cards circulating. Bring it to ComputerKing for a free inspection. We're located in Sham Shui Po, and you can WhatsApp us at 2186 8010 to book a drop-off or ask questions. We've handled over 10,000 cases, and we'll give you an honest assessment.


*This article was written by the ComputerKing senior repair team, with over 15 years of computer repair experience in Hong Kong and 10,000+ cases handled. Last updated: 2026-11-12*

Related articles

Related services

If you need Display output repair, see these service pages: