Monitor Making Strange Noises When Powering On or in Use? Relay Click, Coil Whine, Humming & Speaker Sound Diagnosis Guide

Key Takeaways
Sound is a diagnostic signal, just like the picture: what matters is the kind of sound, when it appears, and what it changes with. Mute the system first to separate speaker sound from body sound, then match the sound type and timing before deciding whether the noise is a normal physical effect or a reason to stop testing.
What Counts as a Strange Monitor Noise
Start by pinning down exactly what is being heard, because "strange noise" covers several different sounds, and each one points in a different direction.
The symptom covered here is sound coming from the monitor itself — the display unit on the desk — when it is switched on, while it is in use, or when it changes mode. That includes a single click at switch-on, repeated clicking, a high-pitched whine, a low hum, a buzz that follows the brightness setting, and sounds that come out of the monitor's built-in speakers. All of those belong here, because the first job is to sort them into kinds before judging any of them.
Three boundaries need to be clear before going any further:
- Sounds from inside the computer case are a different subject. The graphics card fan, the graphics card inductors, the computer power supply, and the motherboard all sit inside the case, and their noises have their own diagnoses. The monitor is a fourth possible location, separate from the three inside the case, and the two have to be kept apart.
- Sounds played through the speakers are content audio, not body sound. A sound that comes out of the monitor's built-in speakers or its headphone socket belongs to the audio path, and it has to be separated out before the monitor body is judged at all.
- Some monitors have no speakers and no internal fan. Many monitors have no speakers at all, and only a small number of models contain an internal cooling fan. A monitor without speakers cannot produce speaker sound, and a monitor without a fan cannot produce fan sound, so the model's own manual is the reference for what it can and cannot do.
If the sound is coming from the monitor on the desk, and the question is which kind it is and what it means, the steps below apply.
Sound Is a Signal, Not a Verdict
A noise on its own is not a diagnosis. The same volume can come from a normal physical effect in one monitor and from a fault in another, and the same fault can sound loud in a quiet room and faint in a noisy one. Volume is affected by the room, the placement, and the resonance of the monitor body, so it cannot be compared directly between two setups.
What can be compared is the kind of sound, the timing of the sound, and what the sound changes with. Those three questions sort monitor noises into a small number of families, and each family has its own next step. The rest of this guide works through the families one by one, then through the comparisons that separate them.
The Seven Families of Monitor Sound
One short click at switch-on or when changing mode
When a monitor switches on or changes mode, circuits inside it switch over, and that switching can produce a single short click. Some monitors click when changing input or when switching between modes, because the internal circuits are being switched. A single click, short, and synchronised with switching on or changing mode, belongs to this family. On its own it is not evidence of a fault.
Repeated clicking, with the monitor failing to stay on
Repeated clicking — click, click, click, over and over — while the monitor fails to come on, or comes on for a moment and then goes off again, belongs to a different family. This pattern points at the protection circuit working in a loop: the power board detects something wrong, cuts the output, then tries to establish it again, and the cycle repeats. The sound itself is the audible evidence of that protection loop. A protection trip needs a full disconnection from the wall to reset; pressing the power button again and again without unplugging will not clear it, because the protection stays latched.
A high-pitched whine or squeal
Inductors — coils of wire on the power board — vibrate when the current through them changes quickly. When that vibration falls within the range of human hearing, it is heard as a high-pitched whine or squeal. The physics is the same as the whine heard from a graphics card's power inductors: the coil vibrates as the current changes, and the frequency is high, so the sound is sharp rather than low. A monitor power board contains inductors too, so the same effect can happen on the monitor side. The useful question is what the whine changes with: whether it follows the brightness setting, follows the picture content, or stays steady regardless.
A low, steady hum
A transformer vibrating at mains frequency produces a low, steady hum — a deep sound rather than a sharp whine. The frequency is far lower than the whine of an inductor, so it is heard as a low hum rather than a squeal. This kind of sound is usually stable and continuous, and it relates less to the load than the other families do. It is the audible counterpart of the mains side of the power board, and it has to be judged on its own terms rather than being confused with the high-pitched families.
A buzz that follows the brightness setting
A buzz whose volume or pitch changes when the brightness is adjusted points at the backlight driver side. The backlight supply switches on and off at a rate that changes with the brightness setting, and the load on that circuit changes with it. When the sound follows the brightness — louder or higher at one setting, quieter or lower at another — the backlight driver circuit is the direction to look. The flicker mechanism behind brightness adjustment belongs to the picture layer, and this guide only deals with the sound that follows the brightness, not with the flicker itself.
Sound from the speakers
Sound that comes out of the monitor's built-in speakers or its headphone socket is content audio, not body sound. The switching state between the monitor's speakers and the headphone socket can stay on the wrong side, so that sound keeps coming from one output when it should come from the other. Many monitors have no speakers at all, which makes this family easy to rule out on those models. Speaker sound and body sound must be separated first, because they belong to entirely different layers and lead to entirely different next steps.
Sound from an internal fan
A small number of monitor models contain an internal cooling fan, and its sound follows temperature or load. This family is an edge case rather than the common one: most monitors have no fan, so fan sound should only be considered after checking the manual for whether the model has one at all. Where a fan exists, its sound rising with temperature is a different pattern from a whine that follows the picture content.
Why Locating a Sound by Ear Is Unreliable
Three components inside a computer case can sit within a few centimetres of each other, and sound reflected off the inside of the case makes it impossible for the ear to tell which one is producing a whine. The same principle applies between the monitor and the computer: the monitor sits next to the case, the two machines are close together, and sound reflected off the desk and the walls limits what the ear can locate.
That is why the diagnosis in this guide relies on comparisons rather than on listening harder. Muting the system, changing the brightness, changing the input, changing the socket, switching off nearby equipment, and swapping the monitor each isolate one variable. A sound that disappears when one thing changes has been located by that change, not by the ear. Tapping or knocking the monitor is not a diagnosis: vibration can make a poor contact disappear temporarily, hiding the clue instead of revealing it.
A Step-by-Step Diagnosis
Work through the steps in order, and change one thing at a time. Changing two things at once destroys the evidence: if the sound stops, there is no way to know which change mattered.
Step 0: Observe first, change nothing
Before touching a cable or a setting, note five things: what kind of sound it is — a single click, repeated clicking, a high whine, a low hum, a buzz, or speaker sound; when it appears — only at switch-on, only when changing mode, continuously, or intermittently; whether it has been there since the monitor was bought or appeared suddenly; whether it is getting louder or staying steady; and whether the picture is normal or shows flickering, a black screen, lines, or the monitor switching itself off or restarting. Write the answers down. A diagnosis that starts from a written record is far more reliable than one that starts from a vague impression of "a weird noise".
Step 1: Separate speaker sound from body sound
Mute the system, unplug the audio cable, and switch the monitor's speakers off if the menu allows it. Then listen again. If the sound disappears with the muting, it belonged to the speaker and audio path, and the direction moves to the audio-path diagnosis. If the sound continues unchanged after muting, it belongs to the monitor body, and the steps below apply. Note that muting only silences the speakers; it cannot silence a body sound, so a sound that survives muting is itself a result — it has already been located to the body.
Step 2: Name the sound family
Match the sound to one of the families above: a single short click synchronised with switching on or changing mode; repeated clicking with the monitor failing to stay on; a high-pitched whine; a low steady hum; a buzz that follows the brightness; or a fan sound that follows temperature. The family is the first fork in the whole diagnosis, and it decides which comparisons come next.
Step 3: Note the timing
Ask when the sound appears. A single click only at switch-on and a continuous hum are two completely different paths. A sound that appears only when changing mode points at the switching circuits. A sound that appears intermittently points at something that changes — a load, a temperature, or an input. A sound that appeared suddenly points at the most recent change; a sound that has been there since purchase points at the character of the model.
Step 4: See what the sound follows
Change one thing at a time and listen after each change: adjust the brightness up and down, and note whether the sound follows it; change the input source or the picture content, and note whether the sound follows the load; move the monitor to a different wall socket, and note whether the sound changes; switch off nearby electrical equipment, and note whether the sound changes. Each change tests one layer — the backlight driver, the load, the mains supply, or the environment — and each result narrows the field.
Step 5: Compare with the time pattern
Ask whether the sound appeared suddenly or has always been there, and whether it is getting louder or staying steady. A sudden appearance points at the most recent change: a move, a new cable, a new socket, a new setting. A sound that has been there since purchase points at the character of the model rather than at ageing. A sound that is gradually getting louder is worth noting and passing on, even if the picture is still normal.
Step 6: Check the accompanying symptoms
Look at the picture and the monitor together. Is the picture flickering, black, showing lines, or freezing? Is the monitor switching itself off or restarting? Is there a smell, unusual heat, or swelling of the body? Sound plus other symptoms together point first at the power or backlight layers, not at the sound alone. A sound on its own and a sound with companions are two different situations, and they should not be judged the same way.
Step 7: Swap the monitor
Using the same mains supply and the same signal cable, connect a different monitor and switch it on once. If the sound follows the original monitor, the fault sits with the monitor. If the sound stays in the same place with a different monitor, the fault sits with the environment or the computer. Change only one thing: do not swap the cable and the monitor at the same time, or the result will be unreadable.
Step 8: When to stop testing
Stop testing immediately, do not keep switching the monitor on, and leave it unplugged if any of the following appears:
- Crackling or popping sounds, or any sound like something bursting
- A burning smell
- Sparks, or any visible damage
- The picture going black, showing lines, or the system freezing at the same time as the sound
- The sound suddenly becoming extremely loud
These signs point toward a fault inside the monitor, and continued testing with power applied can make the damage worse. The right move is to leave the monitor unplugged and send it for a check.
Reading the Sound: Two Tables
The first table turns the sound type into a direction. The second turns the timing into a direction. Use them together: a sound type plus a timing narrows the field far more than either one alone.
| Sound type | What it points to | Next step |
|---|---|---|
| One short click, synchronised with switch-on or mode change | Circuit switching at switch-on or mode change | Note it and watch for change; a single click on its own is not evidence of a fault |
| Repeated clicking, monitor failing to stay on | Protection circuit looping — detecting a fault, cutting output, trying again | Full disconnection from the wall to reset the protection, then a check if it repeats |
| High-pitched whine or squeal | Inductor vibration on the power board, current changing quickly | Test what it follows: brightness, picture content, or steady regardless |
| Low, steady hum | Transformer vibration at mains frequency | Test the mains side: a different wall socket, other equipment switched off |
| Buzz that follows the brightness | Backlight driver side — supply switching rate and load following brightness | Adjust the brightness up and down and record how the sound follows |
| Sound that disappears when muted | Speaker and audio path, not the monitor body | Move to the audio-path diagnosis |
| Sound that follows temperature or load on a model with a fan | Internal fan, where the model has one | Check the manual first — most monitors have no fan |
| Timing pattern | What it points to | Next step |
|---|---|---|
| Only at switch-on, one click | Switching circuits at start-up | Note it; a single click at switch-on is a normal physical effect in many models |
| Only when changing mode | Switching circuits at mode change | Note it; some monitors click when internal circuits switch during a mode change |
| Continuous and steady | Mains or inductor layer running constantly | Test what it follows before judging it |
| Intermittent | Something that changes — load, temperature, or input | Record when it appears and what changed at the same time |
| Appeared suddenly | The most recent change — a move, a new cable, a new socket, a new setting | Look for what changed at the same time and reverse it as a comparison |
| Present since purchase | Character of the model | Note the baseline and watch for change, rather than treating the sound itself as a fault |
| Getting louder gradually | A change worth reporting | Record the trend and pass it on, even with a normal picture |
Cases That Look Similar but Are Not This Problem
Several nearby sounds are easy to confuse with a monitor noise. Sorting them out early saves a lot of wasted effort:
- The graphics card fan is noisy. A fan inside the computer case with a bearing or blade problem belongs to the graphics card fan diagnosis. It is inside the case, not in the monitor, and the monitor swap comparison separates the two.
- The graphics card whines under load. A high-pitched whine from the graphics card's power inductors belongs to the graphics card diagnosis. The monitor is a fourth possible location, separate from the three inside the case, and the two have to be located separately.
- A whine comes from the computer power supply or the motherboard. Whine located among the three components inside the case belongs to the case-side diagnosis. The monitor swap comparison — the sound following the monitor or staying in place — is what separates the monitor from the case.
- Sound comes out of the speakers when a video plays. That is content audio travelling the audio path, and it belongs to the audio-path diagnosis. The mute comparison separates it from body sound in one step.
- The screen flickers at low brightness. Flicker at low brightness belongs to the brightness-adjustment picture layer. The sound that follows the brightness is the only part covered here; the flicker mechanism itself is a separate subject.
- The monitor switches itself off or restarts while in use. That fault is about staying on, not about sound. A noise may accompany it, but the restarting pattern is the main symptom, and it has its own diagnosis.
- A nearby appliance hums or buzzes. Sounds from nearby electrical equipment travel through the air and are not produced by the monitor at all. Switching nearby equipment off as a comparison separates environmental sound from monitor sound.
- The monitor clicks once and then works perfectly. A single click at switch-on, followed by normal operation, is the switching family. It should not be treated as the repeated-clicking family, which comes with the monitor failing to stay on.
Common Misconceptions
- "Any sound means the monitor is broken." Wrong. A relay switching sound and a faint inductor sound can be normal physical effects, not evidence of a fault. The kind of sound, the timing, and what it changes with decide the meaning, not the mere fact that a sound exists.
- "Louder sound means a bigger problem." Wrong. Volume is affected by the room, the placement, and the resonance of the monitor body, and it cannot be compared directly between two setups. A loud sound in a quiet room and a faint sound in a noisy room may come from the same cause.
- "Hearing the sound tells you which part is making it." Wrong. Sound reflects off the desk, the walls, and the inside of the case, and the ear cannot locate it reliably when the monitor and the computer sit close together. Location has to come from comparisons — muting, brightness, input, socket, and the monitor swap — not from listening harder.
- "A monitor sound must be the graphics card." Wrong. The monitor and the computer are two separate machines, and their sounds are two separate lines. The monitor swap comparison is what separates them, and blaming the graphics card before that comparison is a misdiagnosis in this fault.
- "Knocking the monitor will stop the noise." Wrong. Knocking is not a diagnosis, and vibration can make a poor contact disappear temporarily, hiding the clue instead of revealing it. A sound that stops after a knock has not been fixed; it has been masked.
- "Opening the monitor to find the sound source is a reasonable job." It is not. Monitors contain high-voltage parts, opening one carries a real risk, and internal components belong in a workshop. Opening the monitor can also affect any later check.
- "Muting the system fixes the noise." Wrong. Muting only silences the speakers; a body sound does not disappear because the system is muted. A sound that continues after muting is itself a result — it has been located to the monitor body.
- "A sound that appeared suddenly means something has burned out." Wrong. A sudden appearance is only a timing signal, and it has to be read together with the accompanying symptoms — smell, picture faults, heat. A sudden sound with no companions is a different situation from a sudden sound with a burning smell or a black screen.
What to Note Down Before a Check
Bringing a clear record makes a check faster and more accurate. Note the brand and model of the monitor, and whether the manual says it has built-in speakers or an internal fan. Record what kind of sound it is, when it appears, and whether it has been there since purchase, appeared suddenly, or is getting louder. Record what the sound follows — brightness, picture content, input source, socket, or nearby equipment — and the result of the mute comparison, the brightness comparison, and the monitor swap. Add any accompanying symptoms: flickering, a black screen, lines, the monitor switching itself off or restarting, smell, heat, or swelling.
Inspection is charged under the site's published three-tier fee of HK$400–2,800, with the actual figure confirmed after inspection. The shop is at Room 1209, Dali Plaza, Shek Mun. The phone number is 2186 8010 and WhatsApp is 6558 6806. There is no shop in Mong Kok and no on-site service.
Frequently Asked Questions (FAQ)
My monitor clicks once when I switch it on. Is that a fault?
Not necessarily. When a monitor switches on or changes mode, circuits inside it switch over, and that switching can produce a single short click. A single click, short, and synchronised with switching on or changing mode is a normal physical effect in many models. What matters is whether the click is repeated, or whether the monitor fails to stay on afterwards.
My monitor keeps clicking over and over and will not stay on. What is happening?
Repeated clicking with the monitor failing to stay on points at the protection circuit working in a loop: the power board detects something wrong, cuts the output, then tries to establish it again, and the cycle repeats. A protection trip needs a full disconnection from the wall to reset. Pressing the power button again and again without unplugging will not clear it, because the protection stays latched.
How do I tell speaker sound from body sound?
Mute the system, unplug the audio cable, and switch the monitor's speakers off if the menu allows it. If the sound disappears with the muting, it belonged to the speaker and audio path. If the sound continues unchanged after muting, it belongs to the monitor body: muting only silences the speakers, so a sound that survives muting has already been located to the body.
What is the high-pitched whine coming from my monitor?
Inductors on the power board vibrate when the current through them changes quickly, and when that vibration falls within the range of human hearing, it is heard as a high-pitched whine. The useful question is what the whine changes with: whether it follows the brightness setting, follows the picture content, or stays steady regardless. That answer decides which layer the whine belongs to.
What is the difference between a low hum and a high-pitched whine?
A low hum comes from a transformer vibrating at mains frequency: low in pitch, steady and continuous, and related less to the load. A high whine comes from an inductor vibrating as the current through it changes quickly: high in pitch and sharp. The physics is the same; only the frequency differs, so they sound like two completely different sounds.
When the sound changes as I turn the brightness up, does that mean the backlight is faulty?
Not on that evidence alone. A buzz that follows the brightness points at the backlight driver side, because the backlight supply switches at a rate that changes with the brightness setting, and the load on that circuit changes with it. That pattern is a clue, not a conclusion: read it together with the timing, the accompanying symptoms, and the other comparisons before deciding anything.
How do I tell whether the noise is coming from the monitor or the computer?
Use comparisons, not your ears. The monitor sits next to the computer, and sound reflected off the desk and the walls makes it impossible to locate the source by listening alone. Mute the system, change the brightness, change the input, and then swap the monitor using the same mains supply and the same cable. If the sound follows the monitor, it belongs to the monitor; if it stays in place, it belongs to the environment or the computer.
The noise appeared suddenly. Has something burned out?
Not necessarily. A sudden appearance is only a timing signal, and it has to be read together with the accompanying symptoms. A sudden sound with no smell, no picture fault, and no heat is a different situation from a sudden sound with a burning smell, a black screen, or lines across the picture. Look first for what changed at the same time — a move, a new cable, a new socket, or a new setting.
Can I open the monitor to find where the sound is coming from?
No. Monitors contain high-voltage parts, and opening one carries a real risk. Internal components, including the power board and the backlight driver, belong in a workshop. Opening the monitor can also affect any later check, so the sound should be located with the comparisons in this guide and the findings passed on.
When should I stop testing and send the monitor in?
Stop at once if you hear crackling or popping sounds, if there is a burning smell, if you see sparks or visible damage, if the picture goes black or shows lines at the same time as the sound, or if the sound suddenly becomes extremely loud. Leave the monitor unplugged and send it for a check.