GPU Repair Pickup: How to Verify the Fix Before You Leave? Reproducing the Original Fault, Load Testing & Warranty Paperwork Checklist

2026-11-12 | GPU Repair | 16 minutes | HK GPU Fix Editorial Team

GPU Repair Pickup: How to Verify the Fix Before You Leave? Reproducing the Original Fault, Load Testing & Warranty Paperwork Checklist

Key Takeaways

A picture on screen is the weakest proof a repair worked. Reproduce the original fault under the same conditions, run a load test, compare temperatures, fan behaviour and noise against your pre-repair baseline, inspect the card visually, and confirm the warranty in writing before you leave. If the original symptom returns, stop testing and take the card back.

Why "It Turns On" Is the Weakest Evidence

A graphics card that powers on and shows a picture has only proved one thing: its basic initialisation works. That is a long way from proving the original fault has been fixed, and it is the most common trap at pickup time. Many graphics card faults are intermittent. A cracked solder joint or a hairline break in a printed circuit board can make and break contact as the board heats up and cools down, so the fault appears and disappears with temperature. A memory fault can stay silent at idle and only show up after the card has been under load for a while. In both cases, a card that looks fine on the desktop in the first minute can fail again under the exact conditions that made it fail before.

That is why acceptance testing has to be built around the original fault, not around a generic "does it work" check. The question is never "does it show a picture?" The question is "does the thing that was broken still happen under the conditions that used to trigger it?" Everything in this guide follows from that single idea.

Acceptance testing also has a practical side. Once you leave the shop with the card, the next time it fails you will be starting a new conversation: another visit, another explanation, another round of testing. A careful check at pickup costs a little time and saves that whole second round. The record you make during the check — temperatures, fan behaviour, noise, photographs — becomes the evidence you bring back if the fault returns inside the warranty period.

Step 1: Reproduce the Original Fault

Start with the fault itself. Before you hand the card in for repair, you already know what was wrong with it: a game that crashed at a certain point, a screen that flickered after twenty minutes of play, a card that lost its signal under load, a fan that rattled at a certain speed. That trigger is your test.

At pickup, recreate the same conditions as closely as you can. Use the same game, the same workload, the same length of time. If the fault used to appear after a long session, a two-minute desktop check will not reproduce it, and a two-minute check that passes means nothing. If the fault used to appear in one particular game and not in others, running a different game does not test the repair.

If the original symptom reappears during this step, stop. Do not move on to the other steps, do not try different settings, and do not try to work around it. The repair has not held, and the card should go straight back. Trying more things at this point only muddies the record: you want a clean, simple statement — the original fault happened again under the original conditions.

If the original symptom does not reappear, you have earned the right to move on. That is the only conclusion this step supports. It does not prove the card is permanently fixed; it proves the fault did not show up under its own trigger this time. The remaining steps exist to make that conclusion stronger.

Step 2: Run a Load Test

The second step is a load test: a sustained, heavy workload that pushes the card well beyond desktop use. The reason is simple. At idle, a card draws little power, generates little heat, and exercises only a small part of its circuitry. Power delivery, cooling, and memory only show their weaknesses under load. A card can be perfectly calm on the desktop and still fail the moment it is asked to work hard, because the fault lives in the parts of the card that idle never touches.

Commonly used load-test tools include FurMark and 3DMark. Published stress-test guides commonly suggest running FurMark for around twenty to thirty minutes while watching temperature, frame rate, and the screen for artifacts. Shorter published checklists suggest five to ten minutes without a crash or artifacts as a minimum screen. The exact duration is less important than the principle: run the card hard enough, and long enough, for a residual problem to have a chance to appear, and watch it while it runs.

During the load test, watch four things:

Do not walk away while the test runs. The point of the test is observation, and an unattended test that crashes tells you less than a watched test that you can describe precisely: what happened, when it happened, and what the card was doing at the time.

Step 3: Compare Against Your Baseline

A single temperature reading proves nothing on its own. What matters is comparison: how does this card behave now, compared with how it behaved before the repair? That is why the most valuable thing you can bring to pickup is a record made before you sent the card away — a photograph of your monitoring readings, a note of the temperature and fan speed under load, a note of how loud the card was.

If you have that record, compare the new readings against it. A card that now runs noticeably hotter under the same load, or whose fans now spin much faster to hold the same workload, is telling you something has changed, even if nothing has crashed yet. Equally, a card that now runs cooler and quieter than before is a good sign, but it is still only one data point.

There is no universal pass temperature for a graphics card, and this guide deliberately gives none. Different cards, different coolers, different cases, and different room temperatures all move the numbers. A temperature that is normal for one card is high for another. The only honest comparison is the card against itself: the same card, the same workload, before and after the repair. If you do not have a pre-repair record, make one now. Write down the readings from today's load test and keep them. They become the baseline for the next time something goes wrong.

Use a monitoring tool such as GPU-Z or HWiNFO to read the numbers. Note the card model and the amount of video memory shown, and confirm they match the card you sent in. Then record the following during the load test:

What to recordWhy it mattersWhere it comes from
Temperature under loadCompare with your pre-repair reading under the same workloadMonitoring software during the load test
Fan speed under loadA fan working much harder than before suggests cooling has changedMonitoring software during the load test
Noise at loadNew rattles, whines, or vibration are changes worth notingListening during the test
Any artifacts, flicker, or black screensAny of these during the test is a failureWatching the screen during the test
Any crash or driver resetAny of these during the test is a failureWatching the screen during the test
Idle temperature after the testHow quickly the card settles back down after loadMonitoring software after the test ends

Keep this record with the repair receipt. If the card fails again inside the warranty period, this table is the clearest thing you can show: the card passed these checks on this date, under these conditions, and now it does not.

Step 4: Inspect the Card Without Opening It

The fourth step is physical, and it is limited to looking. Do not open the card. Do not remove the cooler, the backplate, or any screws. Opening the card during the warranty period can void the warranty, and it is not part of acceptance testing. Everything in this step can be done with your eyes and ears.

Check that all screws are present and seated. Check the backplate for new bends, scratches, or marks that were not there when you sent the card away — this is where a photograph taken before the repair pays for itself. Check the output connectors: the pins should be straight, with no bent or damaged contacts. Check that the fans spin freely and evenly when the card starts, and that nothing is catching on a cable or a loose label. Listen when the card powers on: any new scraping, clicking, or grinding sound is worth raising before you leave.

Also confirm the card is the card you sent in. Check the model name and the serial number on the label against your receipt or your own photograph. This sounds obvious, and it is exactly the kind of thing that is easy to skip in the relief of getting the card back.

Step 5: Check the Warranty Paperwork

The paperwork is the second half of acceptance. A repair without clear written terms leaves you with nothing to rely on if the fault comes back. Before you leave, confirm the following, in writing:

ItemWhat to confirm
Warranty lengthHow many days the warranty runs, and from which date
What is coveredWhich faults and which parts the warranty covers
What is not coveredWhat is excluded, including damage caused after pickup
Written or verbalWhether the terms are printed on the receipt or only spoken
Receipt and recordsWhether the receipt, the fault description, and the repair description are all present and match

The principle is simple: a warranty scope confirmed in writing is worth having; a verbal promise is hard to rely on later. If the terms are only spoken, ask for them to be written on the receipt. If anything is unclear — what counts as a covered fault, what happens if the same fault returns, whether the warranty covers parts, labour, or both — ask before you leave, while the people who did the work are in front of you.

Pricing is a separate matter from warranty, and it should already have been settled before the repair. The shop's published three-tier repair pricing is HK$400–2,800, with the actual figure confirmed by a quote after inspection. If the amount on the receipt does not match the quote you were given, raise it now, not later.

Step 6: If the Card Fails Again Inside the Warranty Period

A single load test that passes does not guarantee the card will never fail again. Intermittent faults can hide through one test and return later, and a repair can hold for weeks before a weakness shows itself. That is what the warranty period is for, and this step is about what to do when it happens.

Stop using the card as soon as the fault reappears. Do not keep running it in the hope that it will settle, and do not try to fix it yourself. Do not open the card, do not remove the cooler, do not flash the firmware, and do not take it to another shop to be opened first. Any of those steps can void the original warranty. Instead, keep your test record and your photographs, bring the receipt and the paperwork, and take the card back to the shop that repaired it, with a clear description of what happened: the original fault, the conditions that brought it back, and when it happened.

Common Mistakes at Pickup

What This Guide Does Not Cover

This guide covers the moment of pickup: how to test a completed repair before you leave. It does not cover how to read stress-test scores in detail, or how to interpret every monitoring reading — those belong to a guide on stress-test results. It does not cover the full terms of a repair warranty in general, only how to confirm the paperwork at pickup. It does not cover deciding whether a repair is worth doing in the first place — that decision is made before the repair, not at pickup. And it does not cover a new symptom that has nothing to do with the original fault. If a completely different problem appears after pickup, diagnose that symptom on its own terms rather than forcing it through an acceptance checklist.

When to Seek Help

If the original fault reappears at pickup, if the load test crashes or shows artifacts, or if the paperwork does not match what was agreed, do not take the card home and hope for the best. Raise it on the spot. If you are unsure whether a reading or a sound is normal, bring your pre-repair record and your photographs and ask the shop to look at them with you. HK GPU Fix is at Shop 1209, Dali Plaza, Shek Mun. Phone 2186 8010, WhatsApp 6558 6806.

FAQ

Q1: Is it enough if the card shows a picture after the repair?

No. A picture on screen only proves basic initialisation. Intermittent faults — a cracked solder joint that opens as the board heats up, or a memory fault that only appears under load — can stay hidden at idle and on the desktop. Acceptance means reproducing the original fault's trigger conditions, not just seeing a picture.

Q2: How do I reproduce the original fault at pickup?

Use the same conditions that triggered it before the repair: the same game, the same workload, the same length of time. If the fault used to appear after a long session, a short check will not reproduce it. If the original symptom appears, stop testing and take the card back.

Q3: How long should I run a load test before accepting the card?

Long enough for a residual problem to have a chance to appear. Published stress-test guides commonly suggest around twenty to thirty minutes with a tool such as FurMark, while shorter checklists suggest five to ten minutes without a crash or artifacts as a minimum screen. Watch the screen and the monitoring readings for the whole run.

Q4: What should I watch during the load test?

Four things: the picture (any flicker, coloured dots, lines, or black screen is a failure), stability (any crash, driver reset, or restart is a failure), fan behaviour (fans should spin up smoothly and settle), and noise (any new grinding, clicking, or whine is worth raising). Stay and watch the test while it runs.

Q5: How do I compare temperatures with my pre-repair baseline?

Use monitoring software such as GPU-Z or HWiNFO and record the temperature and fan speed under the same workload you used before the repair. Compare the new numbers with your old record. There is no universal pass temperature — the only honest comparison is the same card against itself under the same workload.

Q6: What physical checks should I do without opening the card?

Check that all screws are present, the backplate has no new bends or marks, the output connector pins are straight, and the fans spin freely and evenly. Listen for new sounds when the card powers on. Confirm the model and serial number match your receipt. Never remove the cooler or open the card — that can void the warranty.

Q7: What should the warranty paperwork say?

It should state the warranty length and start date, what is covered, what is not covered, and whether the terms are in writing on the receipt. If the terms were only spoken, ask for them to be written down before you leave. A warranty scope confirmed in writing is the part you can rely on later.

Q8: What should I do if the original fault comes back during the test?

Stop immediately. Do not try other settings or workarounds, and do not move on to the other checks. The repair has not held. Take the card back with a clear description of what happened and under which conditions.

Q9: What should I do if the card fails again inside the warranty period?

Stop using the card, keep your test record, photographs, and receipt, and take it back to the shop that repaired it. Do not open the card, flash the firmware, or take it to another shop to be opened first — any of those can void the original warranty.

Q10: What if a new, unrelated symptom appears after pickup?

Treat it as a separate problem. A new symptom that has nothing to do with the original fault should be diagnosed on its own terms, not forced through the acceptance checklist. Note when it appeared, what the card was doing, and whether it repeats, and bring that record with you if you seek help.

Related articles

Related services

If you need Chip-level GPU repair, see these service pages: