Exported Video Audio Only on One Channel? Mono Export, Channel Mapping & Player Settings Diagnosis Guide

2026-11-21 | GPU Repair | 31 minutes | HK GPU Fix Editorial Team

Exported Video Audio Only on One Channel? Mono Export, Channel Mapping & Player Settings Diagnosis Guide

Key takeaways: An exported file that plays in only one channel while the timeline plays in both is usually a channel-mapping fault, not a broken recording or a faulty earphone. Check the export channel configuration, the track pan and output assignment, and the export bus in turn, changing one setting at a time.

A finished export plays back with sound in only one ear. One channel carries the dialogue, the music and every effect, and the other channel carries nothing at all — not quiet sound, not intermittent sound, but silence from the first frame to the last. Yet when the same material is played back on the timeline in the editor, both ears hear it, the balance sounds centred, and nothing seems wrong. The first instinct is often to blame the earphones, to blame the microphone, or to export the whole programme again and hope the second copy comes out differently. None of those steps addresses the cause, because the cause usually sits in a part of the chain that timeline playback never passes through: the export layer.

The distinction that matters most is between monitoring and exporting. Timeline playback is a monitoring path. The editor is allowed to interpret a clip, centre it, and present it in a balanced way so that the editor can hear what is there. Export is a separate path with its own settings. It takes the timeline, passes it through the track pan controls, the track output assignments, the mix bus, its own channel configuration, and then the audio encoder and the container. A setting in any one of those export-only stages can drop a channel, even when the monitoring path was correct. Timeline playback sounding balanced therefore proves only that the monitoring path was balanced. It proves nothing about the export path, because the two paths diverge at exactly the points where this guide's faults live.

This guide treats the one-sided export as a mapping problem first and a settings problem second. Mapping is the question of which signal goes to which channel: left signal to the left channel, right signal to the right channel, or one signal to both. When the mapping is wrong at export, one channel of the finished file is empty, and no amount of turning the volume up will fill it, because there is no signal there to amplify. Each test below changes one mapping layer at a time and re-exports a short test, so the layer responsible is identified by the change in the finished file, not by guessing.

What shape is this article about?

This article covers only a narrow shape, and five conditions must all hold. First, the subject is a finished exported file: a file that has already been through the export stage. A recording file that itself has sound in only one channel is a recording-level matter, not this guide's shape, because the one-sided sound was already written into the recording before editing began. Second, the timeline plays the same material in both channels, with the balance sounding centred. If the timeline itself plays in only one channel, the problem sits in the timeline or source layer, and it must be divided with recording-layer logic first; it cannot be called an export fault directly. Third, the exported file is silent in the same one channel for its whole duration, from start to finish. It is not silent in some sections and normal in others, it is not silent altogether, it is not merely quiet, and its pitch and speed have not changed. Fourth, the silent channel carries no signal at all — zero, not a low level and not an intermittent level — and the reader must be able to state which side is silent, left or right, because the mapping tests depend on that direction. Fifth, every player that plays the same finished file shows the same one channel silent. If only some players show one channel silent while others play both channels normally, the finished file itself is not empty in one channel, and that is a player-specific direction, not this guide's shape.

Several neighbouring shapes look similar and must not be confused with this one. A recording file with sound in only one channel belongs to the guide on one-channel recordings, identified in this library as article 524, where the fault was decided at the moment of recording. An exported file with no sound at all from start to finish belongs to the guide on a fully silent export, identified as article 537, where the checks are about mute, zeroed faders, and the export audio switch. An exported file in which some sections are silent while others have sound belongs to the guide on partly silent exports, identified as article 522, where the silent positions line up with edit points. An exported file that is quiet in both channels, but not silent in either, belongs to the guide on a quiet export, identified as article 540, where the fault is in loudness or fader level rather than in channel mapping. An exported file whose pitch and speed have both changed belongs to the sample-rate guide, identified as article 504. Game dialogue that is silent while effects and music are normal belongs to the guide on the centre channel, identified as article 525, where the fault is in the centre channel rather than in the left or right channel. Game dialogue that is quiet rather than silent belongs to the guide on game dialogue balance, identified as article 536, where the fault is a balance ratio rather than a channel carrying zero signal. Each of those guides asks a different question, and a step taken from one of them will not diagnose a finished file that is empty in one channel for its whole duration.

The shape also excludes two situations that are easy to mistake for an export fault. If one ear of the earphones is silent for every stereo source, including ordinary music, the fault is in the earphones or in the system balance, not in the file, and no export setting will repair it. If the source recording itself carried a signal in only one channel because it was recorded that way, the timeline may still sound balanced because the editor centred the clip during monitoring, and the export may then reproduce the one-sided source faithfully; that is a source-layer matter, and it belongs with the recording guide, not with the export mapping tests below.

How it works: the chain from the timeline to the finished file

Sound travels from the timeline to the finished file through five gates, and each gate can drop a channel on its own. The gates are clip channel interpretation, track pan and output assignment, the mix bus, the export channel configuration, and encoding and muxing. Timeline playback passes through the first three gates in their monitoring form. Export passes through all five, and the last two exist only on the export path. That is why a timeline can sound balanced while the export comes out one-sided: the first three gates were correct in the monitoring path, and the fault sits in a gate the monitoring path never used.

1. Clip channel interpretation: how the editor reads the clip's channels

A single microphone produces one signal. When that single signal is stored inside a stereo container, the signal sits in the left channel and the right channel is empty. That is not a stereo recording; it is a mono source stored in a stereo container. On the timeline, the editor can interpret that clip as mono and centre it, so that the one signal is heard in both ears during monitoring. The listener hears a balanced timeline, and reasonably assumes the clip is stereo. At export, however, the interpretation layer may hand the clip to the encoder as stereo in its original form, with the left channel carrying the signal and the right channel carrying nothing. The finished file then has sound in one channel only. The key point is that timeline monitoring can dress up a clip's channels, and export does not necessarily follow the same dressing. The check for this layer is to read how the clip is interpreted — mono or stereo, and which source channel carries the signal — and to compare that reading with what the finished file contains.

2. Track pan: which side each track sends its sound to

Every audio track carries a pan control, sometimes called a balance control, which decides whether the track's sound goes to the left, to the right, or to the centre. A pan control pushed fully to one side sends that whole track to one channel only. During timeline monitoring, a pan pushed to one side would be heard in one ear, so the shape of this guide — a balanced timeline and a one-sided export — excludes a pan that is wrong in the monitoring path. The pan layer still has to be checked at export, because an export preset, a track output assignment, or a bus setting can override the monitored pan, and because a project may contain several tracks, of which one carries the dialogue and another carries the music, and only one of them may be panned to one side. The check is to read the pan position of every track, one by one, and to write down whether each one sits centred. A track whose pan is centred in the mixer but whose sound still arrives in one channel only in the export points away from this layer and toward the export channel configuration or the export bus.

3. Track output assignment and bus routing: which bus each track feeds

After pan, each track is assigned to an output, and the tracks are combined into a mix bus. In DaVinci Resolve the main bus in the Fairlight page is Bus 1, and in Premiere Pro the equivalent is the sequence output mapping or the track output assignment. The fully silent export guide deals with the case where a track has no routing at all: a track that feeds nothing contributes nothing, and if every track feeds nothing, the whole file is silent. This guide deals with the next case along: routing exists, but it feeds only one side, or the export renders a bus that is not the main mix. A delivery page that has been set to render a single source track instead of the main mix, for example, will produce a file that carries only what that one track carried — and if that track was a mono source, the file will be one-sided. The distinction between "no routing" and "routing that feeds only one side" is the distinction between article 537 and this guide, and the two must not be mixed up. The check is to read, for every track, which output or bus it is assigned to, and then to read which bus the export itself is set to render.

4. Export channel configuration: the setting that exists only at export

The export settings carry their own channel configuration, and that configuration does not follow the sequence settings. This is the most important gate in this guide, and it is the one most often missed, because nothing on the timeline shows it. An Adobe Community reply states the point directly: "The setup for what's stereo and what's mono happens during export, not in your sequence settings." In Premiere Pro the setting is found in the export settings, under Audio, in the Audio Channel Configuration section, where Stream 1 can be set to Stereo or where mono channels can be added; accepting a default preset will output stereo regardless of the sequence, according to another Adobe Community reply, which states that "if you accept the default export presets they will Stereo the output regardless" and that the audio configuration must be visited during export and set to the intended channel count. In DaVinci Resolve the equivalent is on the Deliver page, where the audio bus and channel layout are chosen. A configuration that asks for one channel, or that maps only one source channel into the output, will produce a finished file that is empty in one channel, even though the timeline was balanced. Because this gate is export-only, it cannot be excluded by listening to the timeline; it can only be excluded by opening the export settings, writing the configuration down, and changing it in a short test export to see whether the finished file follows the change.

5. Encoding and muxing: the last write into the file

Audio encoding and video encoding are two separate jobs, and the container is written by a third step, the muxer. The audio encoder and the muxer can lose a channel while the picture stays perfect, because the picture path and the audio path do not share a gate at this stage. That does not mean the encoder should be blamed first. A finished file that is one-sided from a single export proves only that one channel is empty in that file; it does not prove which gate emptied it. The encoder layer is separated from the configuration layers by the short test export: if changing the channel configuration changes the finished file, the encoder was following the configuration; if no configuration change changes the finished file, and the timeline, pan, and bus readings are all correct, then the encoder or container layer becomes the remaining direction to examine, by changing the encoder or the container in a further short test.

GateWhere it sitsWhat it does when wrongHow it shows up
Clip channel interpretationEach clip, before the trackA mono source in a stereo container is passed through as stereoTimeline sounds centred, export is one-sided
Track panEach audio trackSound is sent to one side onlyThat track is one-sided in the export
Track output assignment and bus routingBetween tracks and the mix busTracks feed only one side, or the export renders a single source trackMain mix is balanced, export carries one track only
Export channel configurationExport settings onlyOutput is configured for one channel, or only one source channel is mappedTimeline is balanced, every export is one-sided in the same way
Encoding and muxingAudio encoder and containerA channel is lost while the file is writtenPicture is normal, one audio channel is empty

Mono, stereo and dual mono are not the same word

Three terms are used loosely in editing discussions, and mixing them up leads directly to the wrong repair. Mono means one signal, heard the same in both ears: a single microphone is a mono source. Stereo means two signals, left and right, that are different from each other. A mono source stored in a stereo container, with the right channel empty, is not a stereo recording, even though the file has two channels. Dual mono means two independent mono signals, one in each channel — for example a lavalier microphone on one side and a boom microphone on the other — and a guide from Hollyland states that this case should be treated as dual mono, not as stereo. The repair for each case is different: a mono source needs to be centred or copied to both channels, a stereo source needs its two channels preserved, and a dual-mono source needs each channel handled as its own signal. Writing "make it stereo" without saying which of these is meant will not diagnose anything.

Downmixing must also be kept separate from copying. Downmixing mixes several channels into fewer channels. A guide from fairtoolbox states that repairing a recorded one-sided file requires copying the good channel to the silent channel, not mixing the two channels into mono, because mixing averages the two channels and, according to that guide's test tone, drops the level by about half, around 6 dB. That figure comes from the guide's own test tone and has not been verified by this site, and it is reported here at the same evidence level. In the export layer the same distinction applies: exporting a mono downmix is a diagnostic test, not a repair of the original file. It can show whether the mapping layer is at fault, and it does not change the original finished file. Copying and mixing are two different actions, and they must not be written as if they were the same.

Where the channel settings live in each editor, kept separate

DaVinci Resolve and Premiere Pro put their channel settings in different places, and the two must not be mixed up. In DaVinci Resolve, a clip's channels are set in the Media Pool by right-clicking the clip, choosing Clip Attributes, then Audio, then Format, setting it to Mono, and choosing the embedded channel that carries the signal as the Source Channel — Embedded Channel 1 if the left channel carries the sound, Embedded Channel 2 if the right channel does. On the timeline, a clip's channels can be mapped in the Inspector, under Audio, in Channel Mapping, where the same source channel can be mapped to both the left and right outputs. In the Fairlight page, the track type can be changed to Stereo, and on the Deliver page the output bus and channel layout must be checked to confirm that the main mix, not a single source track, is being rendered. In Premiere Pro and Media Encoder, the channel configuration is in the export settings, under Audio, in Audio Channel Configuration, and the sequence output mapping and track output assignments decide which tracks feed the output. In Shotcut, the output panel's Audio tab sets the codec, channels and sample rate, and all unmuted tracks are mixed down to the stereo output. The panel names and the exact layout differ between versions, and the descriptions here follow the external guides named at the end of this article; they should not be read as guaranteed to match every version.

Diagnostic steps: eight tests in order

The order below matters, because each step narrows the fault to one layer before the next step is attempted. Only one thing is changed at a time, and the finished file is checked again after each change. A short test export is used for every comparison, so that each change can be checked quickly without re-exporting the whole programme for every test. Write every result down before moving on: which side is silent, which setting was read, and what the short test export contained.

Step 1 — Confirm the shape and name the silent side

Confirm that the exported file is silent in the same one channel for its whole duration, and that the other channel is normal throughout. Then play the same material on the timeline and confirm that both channels are heard, with the balance sounding centred. Write down which side is silent in the finished file — left or right — because every mapping test that follows depends on that direction: a left-silent file points at the left source channel being lost, and a right-silent file points at the right one. Also write down the editor and its version, the export preset, and the players used. If the timeline is also one-sided, stop: the shape is not this guide's shape, and the recording-layer logic of article 524 must be used first.

Step 2 — Swap the earphones left and right, then change earphones and machine

This is a shared playback check, already used in the recording guide, and it separates the earphones from the file. Swap the earphones left and right and play the finished file again. If the silence follows the earphone — the side that was silent moves to the other ear — the fault is in the earphones or in the system balance, not in the file. If the silence stays on the same side of the file, the fault is in the file layer, and the diagnosis continues. Then play the same file through a different pair of earphones or speakers, and on a different machine if one is available, and write down whether the same channel is silent in each case. A file that is one-sided on every device and through every pair of earphones has an empty channel in the file itself, and the export layers below are the place to look.

Step 3 — Play the file with Windows mono audio mixing switched on

Windows offers a mono audio setting that mixes the two channels together before playback. Switch it on and play the finished file again. If sound is now heard in both ears, the fault sits in the channel mapping layer: one channel of the file carries the signal, and mixing the two channels together makes that signal audible on both sides. If the file is still silent on one side even with mono mixing on, the file itself has one channel empty in a way that mixing does not rescue, and the diagnosis continues to the waveform check. This is a shared check from the recording guide, and it is used here as a mapping indicator, not as a repair: switching mono mixing on changes what is heard, and it changes nothing in the file.

Step 4 — Compare the two channels as waveforms in an editor

Open the finished file in an editor and display its waveform with the two channels shown separately, then compare it with the source clip's waveform shown the same way. In the finished file, one channel's waveform should sit on the zero line for the whole duration while the other channel shows a normal waveform; that picture confirms that the finished file itself has one channel empty, rather than the player hiding it. In the source clip, check whether one channel is already empty: if the source is empty in one channel and the timeline only sounded balanced because the editor centred it, the fault is in the source layer, and the export mapping tests below will not repair it. This step is the mirror of the recording guide's waveform check, applied here to the finished file against its source, and it is a supporting check, not one of the three new export tests.

Step 5 — Compare the export channel configuration, then change it in a short test export

This is the first of the three new export-layer tests, and it is the most decisive one in this guide. Open the export settings and write down the audio channel configuration exactly as it stands: how many channels the export is configured for, whether Stream 1 is set to Stereo, and whether any mono channels have been added. Then change the configuration and make a short test export — for example, set the configuration explicitly to stereo with two channels, where it was previously left on a default or on a single channel — and check whether the finished file's channel behaviour follows the change. If the short test export now carries sound in both channels, the export channel configuration was the layer at fault, and the full programme can be exported with that configuration. If the short test export is one-sided in exactly the same way, the configuration layer is excluded, and the diagnosis moves to the track layer. The fully silent export guide checks only whether the Export Audio switch is on, together with the codec and the sample rate; it does not use the channel count as a diagnostic variable, and the partly silent export guide uses its output-settings layer only as a negative check that the switch was on. Neither of them tests the channel configuration in the way this step does.

Step 6 — Compare the track pan and output assignment of every track

This is the second of the three new export-layer tests. Work through the tracks one by one. For each track, read its pan position and write down whether it sits centred, and read its output assignment and write down which bus or output it feeds. A pan pushed fully to one side makes that whole track one-sided, and an output assignment that feeds only one side of the bus has the same effect for that track. If one track is panned to one side, or assigned to feed only one side, that track is the suspect, and the test is to return its pan to centre or its assignment to the main mix, then make a short test export and check whether both channels now carry sound. The neighbouring guides deal with mute, solo, level and whether routing exists at all; none of them treats pan direction — where the sound goes, rather than whether it exists — as a diagnostic variable. The word "pan" in its audio sense does not appear as a diagnosis step in those guides, and the pan checks in other contexts, such as camera movement or canvas movement, are different meanings of the same word and must not be confused with it.

Step 7 — Compare the export bus and the rendered object

This is the third of the three new export-layer tests. Check what the export is actually rendering: the main mix, or a single source track. In DaVinci Resolve, check on the Deliver page which output bus has been selected, and confirm that it is the main mix rather than a single source track; a guide from davinciresolveclub states the point directly: "The timeline is balanced, but the export is one-sided — Check the selected output bus and channel layout on the Deliver page. If you mean to deliver the stereo mix, make sure you aren't rendering a single source track." In Premiere Pro, check the sequence output mapping. If the export was rendering a single source track, change it to render the main mix and make a short test export. If the short test export now carries both channels, the bus or rendered-object layer was the fault. The fully silent export guide deals with bus routing as a question of whether routing exists — no routing means silence — while this guide deals with routing that exists but delivers only one side, and the two questions must be kept apart.

Step 8 — Confirm with a short test export, changing only one thing

For every change, re-export a short test section only, and change only one thing at a time: the channel configuration, one track's pan, one output assignment, or the export bus, never two or three together. After each change, check the new file's channel layout — in MediaInfo, where the channel layout is shown as a field, and by listening through both channels — and write the result down next to the change that produced it. Re-exporting with the same settings will produce a file that is one-sided in exactly the same way, so a second export on its own repairs nothing; only a changed setting changes the result. As a supporting check, a mono downmix export can be made: export with mono downmix switched on and make a short test, and if the mono file carries sound in both ears, that points at the export channel mapping layer, while a mono file that is still one-sided points back toward the source or timeline layer. That downmix is a test, not a repair of the original file. Once a short test export carries sound in both channels, export the full programme with those settings and check the full file once more, because a short test confirms the direction of the change and the full export confirms the result.

TestWhat is changedWhat a change in the result means
Export channel configurationChannel count and mapping in the export settingsFile follows the change: configuration layer at fault
Track pan and output assignmentOne track's pan, or one track's output assignmentFile follows the change: that track was the suspect
Export bus and rendered objectWhich bus or track the export rendersFile follows the change: bus or rendered-object layer at fault
Mono downmix export (supporting)Export set to mono downmixBoth ears hear sound: mapping layer; still one-sided: source or timeline layer
Earphone swap and mono mixing (shared)Earphones swapped, or Windows mono mixing onSilence follows the earphone: playback layer; sound appears in both ears: mapping layer

Boundaries: what this article does not cover

A recording file with sound in only one channel, where the timeline itself plays in only one channel, is article 524. The fault was written into the recording, and the export mapping tests in this guide cannot repair it. A fully silent export is article 537, where the checks are about the Export Audio switch, mute, and zeroed faders. A partly silent export, with some sections silent and others audible, is article 522, where the silent positions line up with edit points. A file that is quiet in both channels is article 540, where the fault is in loudness or fader level. A file whose pitch and speed have both changed is article 504, where the fault is in the sample rate. A file that is silent in only some players, while other players play both channels normally, belongs to the channel and phase direction of article 522, not to this guide, because the finished file itself is not empty in one channel. Game dialogue that is silent while effects and music are normal is article 525, where the fault is in the centre channel. Game dialogue that is quiet is article 536, where the fault is a balance ratio. Earphones that are silent in one ear for every stereo source, including ordinary music, belong to the earphone or balance layer, not to the file layer.

Two further points sit outside this guide even though they feel close to it. The recording-layer settings of OBS, including its Downmix to Mono option and its audio interface input mapping, belong to the recording stage and must not be written as export repairs; the export mono downmix in Step 8 is a different panel, at a different stage, and the two must be kept apart. The Export Audio switch belongs to the fully silent export guide: it is a master switch, and switching it off removes the whole audio track, so it cannot explain a file that has sound in one channel and silence in the other.

Common misconceptions: seven claims that mislead

  1. "One channel has sound, so the other channel must be broken." Wrong. A single microphone produces only one signal, and the fault can sit in the mapping layer, with nothing broken at all. The microphone, the earphones and the file can each be intact while the mapping is wrong.
  2. "If the timeline sounds balanced in both ears, the export must sound balanced too." Wrong. The export has its own channel configuration that does not follow the sequence settings, as the Adobe Community reply quoted above states. A balanced timeline proves only that the monitoring path was balanced.
  3. "Switching on Downmix to Mono repairs the file." Wrong. Downmixing is a diagnostic test, not a repair of a finished file. A mono downmix export can show whether the mapping layer is at fault, and it does not change the original finished file.
  4. "Exporting as mono is the same as repairing it." Wrong. Copying and mixing are two different actions. Copying the good channel to the silent channel fills the empty channel; mixing the two channels into mono averages them, and according to the fairtoolbox guide's test tone the level drops by about half, around 6 dB, a figure that has not been verified by this site.
  5. "Exporting again repairs it." Wrong. Exporting again with the same settings produces a file that is one-sided in exactly the same way. Only a changed setting changes the result.
  6. "Adding a 'fill left with right' effect is the confirmed repair." Wrong. That phrase comes from a forum reply quoted in article 522, where the reply suggested trying a "fill left with right" audio effect; the case itself reported no confirmed result, and phase was only a suspected direction there. It must not be written as a confirmed repair in this guide.
  7. "The graphics card must be at fault." Wrong. The audio path runs from the mix to the audio encoder and then to the container, and it does not pass through the video encoder. A completed export that is one-sided in audio, with normal video, is not a graphics card symptom.

FAQ

My exported file has sound in only one channel, but the timeline plays in both. Is the recording broken?

No. If the timeline plays the same material in both channels with a centred balance, the recording and the timeline are not the shape of the fault. The difference between the two playbacks points at the export layer: the export channel configuration, the track pan or output assignment, or the export bus. Work through the three export tests in order, changing one setting at a time and making a short test export after each change, and the layer that follows the change is the cause.

How do I tell which channel is silent, and why does it matter?

Play the finished file through earphones and note whether the left or the right ear is silent, then confirm it by looking at the two channels as separate waveforms in an editor: the silent channel's waveform sits on the zero line for the whole duration. The direction matters because the mapping tests depend on it — a left-silent file points at the left source channel being lost, and a right-silent file points at the right one — and because the clip settings in Resolve ask which embedded channel carries the signal.

I swapped my earphones left and right and the silence moved to the other ear. What does that mean?

It means the fault is in the earphones or in the system balance, not in the file. When the silence follows the earphone, the file is carrying sound in both channels and one earpiece is not reproducing it. Change the earphones, or check the system balance control, and play an ordinary stereo music file as a reference: if that file is also one-sided through the same earphones, the export is not the layer at fault.

The export channel configuration is already set to stereo, but the file is still one-sided. What next?

Check the track layer, then the bus layer. Read the pan position of every track and confirm each one sits centred, read the output assignment of every track and confirm each one feeds the main mix, and then check on the Deliver page or in the sequence output mapping which bus the export is rendering. If the export is rendering a single source track instead of the main mix, change it to the main mix and make a short test export. A stereo setting in the export dialogue does not help if the sound arriving at that dialogue is already one-sided.

Will switching on mono downmix at export repair my finished file?

No. A mono downmix export is a diagnostic test, not a repair of the file that already exists. If the mono test file carries sound in both ears, that points at the export channel mapping layer, and the handling is to correct the mapping in the export settings and re-export the programme. If the mono test file is still one-sided, that points back toward the source or timeline layer. The original finished file is unchanged by either test.

I exported the same timeline twice and got the same one-sided file. What should I change?

Change a setting, not the export count. Re-exporting with the same settings produces the same channel layout. Change one thing at a time — the export channel configuration, one track's pan, one output assignment, or the export bus — make a short test export, and check the new file's channel layout in MediaInfo and by listening through both channels. When the result follows the change, that layer is the cause, and the full programme can then be exported with those settings.

If the fault still cannot be divided

Write down which channel is silent in the finished file, whether the timeline plays in both channels, the export channel configuration as it stands, the pan position and output assignment of every track, which bus the export is set to render, and the result of each short test export, and bring that written record with a copy of the finished file and the project file if it is available. The exact panel names for the export channel settings differ between versions, and the descriptions in this guide follow the external guides named in the research notes; they should not be read as guaranteed to match every version. Bring the written record described above to Room 1209, Dali Plaza, Shek Mun for inspection. The telephone number is 2186 8010 and WhatsApp is 6558 6806. There is no Mong Kok shop, and there is no on-site service. The site's published three-tier fee is HK$400–780, HK$480–1,380, and HK$680–2,800, an overall range of HK$400–2,800, with the actual fee quoted after inspection.

Related articles

Related services

If you need Chip-level GPU repair, see these service pages: